Corrosion Monitoring Technologies for Cracked Gas Compressors
Prevent failure and keep cracked gas compressors from causing unplanned downtime in your ethylene production facility.
Prevent downtime by detecting corrosion in amine units
The cracked gas compressor is critical for cooling down the hot gases in an ethylene plant. Any corrosion issue in this area will potentially stop the production of the entire plant. Corrosion monitoring helps raise alarms immediately when the rate of corrosion is too high, to avoid an outage. Corrosion data is also useful to then look back and understand what conditions influenced corrosion when they were high, for more informed decision making in the future.
Kliknij, aby kontynuować czytanie Prevent downtime by detecting corrosion in amine units
Product Solutions
Get ongoing visibility of corrosion and erosion trends in real-time with unique ultrasonic sensors that continuously measure pipe thickness. Optimized for use in the chemical industry, the Rosemount ET310C is non-intrusive and battery-powered, allowing for quick and straightforward magnetic installation on any metal. The reliable, accurate wall thickness data delivered via a
WirelessHART® network from the Rosemount ET310C to Plantweb™ Insight can help you make better decisions regarding pipe maintenance and replacement.
- Accurately identify corrosion and erosion trends, avoiding unplanned outages and incidents
- Perform predictive maintenance and extend runtimes, with the confidence of continuous asset integrity data
- Maximize asset utilisation and production capacity with real-time asset health information at desk.
Temperature Range
May be used on metal with a service temperature up to 160 °C (320 °F)
Communication Protocol
WirelessHART®
Battery Life
9 years (BP20E power module)
Get ongoing visibility of corrosion and erosion trends in real-time with unique ultrasonic sensors that continuously measure pipe thickness. The ET210 Sensor system is non-intrusive and battery-powered, allowing for quick and straightforward magnetic installation. The reliable, accurate wall thickness data delivered via a WirelessHART® network from the ET210 system to the accompanying software can help you make better decisions regarding pipe maintenance and replacement.
- The wall thickness sensors use EMAT technology and are capable of measuring through external protective coatings enabling continuous operation in upstream applications
- Accurately identify corrosion and erosion trends while avoiding inefficient and potentially unsafe manual inspection methods
- Easy, intuitive and non-intrusive installation enables a quick method to automate without the cost of wiring
Temperature Range
from -40 °C (-40 °F) up to 120 °C (250 °F)
Communication Protocol
WirelessHART
Battery Life
9 years (BP20E power module)
Get ongoing visibility of corrosion and erosion trends in real-time with unique ultrasonic sensors that continuously measure pipe thickness. The ET410 Sensor system is non-intrusive and battery-powered, allowing for quick and straightforward magnetic installation. The reliable, accurate wall thickness data delivered via a WirelessHART® network from the ET410 system to the accompanying software can help you make better decisions regarding pipe maintenance and replacement.
- May be used on metal with a service temperature up to 270°C (518°F)
- The wall thickness sensors use EMAT technology enabling easy installation and continuous operation in downstream applications
- Accurately identify corrosion and erosion trends while avoiding inefficient and potentially unsafe manual inspection methods
Temperature Range
From -40 °C (-40 °F) up to 270 °C (518 °F)
Communication Protocol
WirelessHART
Battery Life
9 years (BP20E battery pack)
Get ongoing visibility of corrosion and erosion trends in real-time with unique ultrasonic sensors that continuously measure pipe thickness. The ET310 Sensor system is non-intrusive and battery-powered, allowing for quick and straightforward magnetic installation. The reliable, accurate wall thickness data delivered via a
WirelessHART™ network from the ET310 system to the accompanying software can help you make better decisions regarding pipe maintenance and replacement.
- May be used on metal with a service temperature up to 160 °C (320 °F)
- The wall thickness sensors use EMAT technology and are capable of measuring through external protective coatings enabling continuous operation in upstream and downstream applications
- Accurately identify corrosion and erosion trends while avoiding inefficient and potentially unsafe manual inspection methods
Temperature Range
May be used on metal with a service temperature up to 160 °C (320 °F)
Communication Protocol
WirelessHART
Battery Life
9 years (BP20E power module)
Get ongoing visibility of corrosion and erosion trends in real-time with unique ultrasonic sensors that continuously measure pipe thickness. The WT210 Sensor system is non-intrusive and battery-powered, allowing for quick and straightforward installation. The reliable, accurate wall thickness data delivered via a WirelessHART® network from the WT210 system to the accompanying software can help you make better decisions regarding pipe maintenance and replacement.
- The wall thickness sensors use breakthrough waveguide technology, enabling continuous operation even at temperatures of up to 600 °C (1100 °F)
- Accurately identify corrosion and erosion trends while avoiding inefficient and potentially unsafe manual inspection methods
- Easy, intuitive and non-intrusive installation enables a quick method to automate without the cost of wiring
Temperature Range
<= 600 °C (1100 °F)
Communication Protocol
WirelessHART
Battery Life
9 years (BP20E power module)
